Generac 10000003275 Controller Click to zoom

Generac 10000003275 Evolution 2.0 Wi-Fi Controller Assembly for 2020+ Air-Cooled Home Standby Generators (Replaces 10000003293)

MPN 10000003275

In stockController

Overview

The Generac 10000003275 is the factory controller assembly (Generac description: ASSY CONTROLLER 2020 AC HSB) used on Wi-Fi equipped, air-cooled Generac home standby generators built from 2020 onward. It is the Evolution 2.0 control panel (sold as Sync 3.0 on Honeywell-branded units) and is the current replacement for controller 10000003293. If your generator's display is dead, the controller has failed, or it was damaged by a surge, this is the genuine part to restore it.

Key features

  • Genuine Generac part: new OEM controller assembly, not rebuilt.
  • Evolution 2.0 / Wi-Fi platform: for generators that came from the factory with Wi-Fi.
  • Replaces 10000003293: the 10000003275 is the replacement for the earlier 3293 controller.
  • Current firmware: ships at Generac's latest revision, so the REV number on your old board does not need to match.
  • No activation code: the replacement panel does not need to be activated with a dealer code.

Fits

  • Generators: Generac air-cooled home standby units built 2020 and later that were equipped with Wi-Fi (Evolution 2.0). Generac-built units sold as Honeywell, Guardian, Siemens, Carrier, Watchdog, Centurion, Eaton and Bryant usually use the same controller.
  • Does not fit: non-Wi-Fi Evolution 1.0 generators, which use controller 0J8371C. This panel cannot be used to add Wi-Fi to an older generator.
  • How to confirm fitment: check the part number on the label of your existing controller and have your generator's model and serial number (data plate inside the enclosure) ready. Controllers are serial-number specific, so send us those numbers and our team will confirm the match before you order.

Specifications

Brand Generac
MPN 10000003275
Also listed as GEN10000003275, ASSY CONTROLLER 2020 AC HSB
Controller platform Evolution 2.0 (Sync 3.0 on Honeywell units)
Connectivity For Wi-Fi equipped generators
Generator type Air-cooled home standby (HSB)
Production years 2020 to current
Replaces 10000003293
Evolution decal Not included (decal 0K0926 sold separately)
Service manual Generac diagnostic repair manual 10000041488
Condition New, genuine OEM

Frequently asked questions

Will the 10000003275 work on a generator without Wi-Fi?

No. It is the Evolution 2.0 controller for generators that shipped with Wi-Fi. Non-Wi-Fi Evolution 1.0 generators use controller 0J8371C, and the two cannot be swapped.

Does 10000003275 replace controller 10000003293?

Yes. The 10000003275 is the replacement for the 10000003293 controller. The reverse does not apply: a 3293 cannot replace a 3275.

Does the new controller need an activation code?

No. The replacement panel does not need to be activated with a code the way the original generator was.

Is the Evolution decal included?

No. The front Evolution decal is not included. You can move the decal from your old controller or order decal 0K0926 separately.

Can I add Wi-Fi to my older generator with this controller?

No. You must use the same controller version your generator was built with. This panel does not add Wi-Fi to an Evolution 1.0 generator.

Who should install it?

We recommend a qualified technician who can check the generator's output voltage and frequency after the swap to confirm correct calibration.

How do I confirm this is the right controller?

Read the part number on your current controller's label and send us your generator's model and serial number. Our team will confirm fitment before you order.